Saturday, April 14, 2012

2010 Ford Mustang Condenser core Diagram?

Condenser core removal diagrams and info.

In this procedure following things are to be removed:---
Remove the 2 upper condenser bolts.
Please note tighten to 80 inch lbs. (9 Nm) while you re-install the nuts.

Then remove the 9 lower radiator air deflector screws,once the screws are out,lower the air deflector.

Remove the condenser outlet fitting nut and disconnect the fitting. Discard the O-ring seal and gasket seal and use new seal. To install, tighten to 133 inch lbs. (15 Nm).

Now remove the 2 lower condenser nuts and position the power steering cooler line aside. While you reinstall tighten the nuts to 80 inch lbs. (9 Nm).

Now the condenser core is loose .The condenser core must be removed from below the vehicle.

See the diagram shown below:----

There are in all 2diagrams.See both the diagrams.

Diagram number 1





Diagram number 2




For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

2009 FORD condenser core Diagram?

Ford Condenser core removal diagram for 2009 Ford vehicles.

In this Procedure lower radiator air deflector has to be removed
After that condenser outlet fitting nut has to be removed.
While installing this nut Follow this specs: tighten to 71 inch lbs. (8 Nm).
Now Remove power steering fluid cooler nuts.There are two nuts,remove both of them.
Position the cooler line carefully to one side.Once this is done the condenser core can now be removed.

Exploded view of the condenser core is shown 



For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html



2009 Ford Mustang condenser core?

See below the Condenser core Diagram for 5.4L Engine

To remove condenser core front bumper has to be removed.
There are pin-type retainers that you have take out,then remove both right and left side Air deflectors,this will let the condenser core to come apart

Detaching the condenser core Shown below:----



For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html



A/C compressor assembly Diagram?

 A/C compressor assembly Diagram shown for -Ford 4.6L and 5.4 engines,

To remove AC compressor the drive belt has to be removed from AC pulley.

Loosen the compressor manifold bolt and detach the compressor manifold.
Please don't use the same old seal,instead use new O-ring seals.

The Following has to be remove to take apart AC compressor :---

Remove the 2 power steering pressure hose bracket bolts.
Disconnect the crankshaft position sensor electrical connector.
Disconnect the field coil electrical connector.
Detach the 2 wire harness retainers from the A/C compressor studs.
Remove the 3 A/C compressor studs.


See the Diagram shown below for AC compressor Assembly:----


For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html



2010 Ford 4.0L A/C compressor Diagram?

AC Compressor removal diagram for Ford Vehicles.
Please Note this Warning and Detail:---
If installing a new A/C compressor, the A/C clutch disc and hub, A/C compressor pulley and A/C clutch field coil must be inspected and transferred from the old unit to the new unit if suitable for reuse.


To remove the compressor

Remove the line bracket nut.
Remove the compressor manifold and tube bracket nut and detach the compressor manifold and tube.
Remove the upper LH compressor nut.
Remove the 2 upper compressor studs.
Remove the lower LH compressor stud.
Remove the compressor bolt.
Remove the A/C compressor.

See below A/C compressor-4.0L engine Diagram:-----


For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html




2010 Ford Mustang blower motor

See below the 2010 Ford Mustang blower motor diagram

To replace the blower motor,right side lower instrument panel insulator has to be taken out.

Then unplug blower motor speed control electrical connector.

The blower motor is fitted by screws,remove the screws and lift out the blower motor .

Diagram showing Removing and installing the blower motor





For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html



Friday, April 13, 2012

2010 Ford Vacuum control motor Diagram?

Below is the Ford Vacuum control motor-air inlet duct door Diagram shown:---

To remove this part the glove box compartment has to be lowered down.

Then disconnect the air inlet mode door actuator electrical connector.

Remove the 2 air inlet mode door actuator screws.
Remove the air inlet mode door actuator.

See the diagram shown below:---



For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html


Blend Door Actuator-RH Dual Zone EATC Ford Mustang 2010

2010 Ford Mustang blend door actuator right hand side diagram is shown below

The diagram shows Removing and installing the RH temperature blend door actuator (dual zone EATC)







For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html

2010 Ford Mustang blend door actuator?

Below is the 2010 ford mustang Blend door actuator removal diagram:---

Temperature Blend Door Actuator-LEFT HAND SIDE

Blend door actuator is fitted by simple removable screws.





For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html


Mode door actuator Ford Mustang 2010

Below is the ford mustang Air inlet Mode door Actuator removal diagram Shown.

The mode door actuator is connected by screws and can can be removed once the Glow box Compartment is lowered:----
Removing the air inlet mode door actuator







For All types of Car models and brands help

Go to Newly Launched


FREE Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

&

Complete Car repair Help FREE?

http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html